Ultratape EXTREME tape SILICON TAPE no stickers AUTO SEALING 25.4 mm x 3m TRANSPARENT MATT

Ultratape EXTREME tape SILICON TAPE no stickers AUTO SEALING 25.4 mm x 3m TRANSPARENT MATT

3,08 [+22% VAT]

  € 3,42 [+22% VAT]


REQUEST COST BEFORE PAYMENT


 

RELATED PRODUCTS

 
 
 
 
 
Product code 10000ST
EAN 8028653012050
Category ADHESIVE TAPES
Brand MOCAP
Availability

Tip a friend

More questions ?

 
pin it

Ultratape extreme tape sealing tape no silicone adhesives car 25.4 mm x 3m transparent opaque tape is made of a special silicone material that can be stuck (sticking) only to itself. the tape has no adhesive and leaves no residue when it is removed; It stretches up to 300%, adapting to irregular shapes. the tape melts, creating a permanent seal airtight and liquido.È excellent for wrapping cables and wires, isolating at 8000 volts, it does not melt up to 500f (260c) and is resistant to UV rays and to atmospheric agents like no other tape. https://www.youtube.com/watch?v=4rterfnh07q https://www.youtube.com/watch?v=4rterfnh07q available in rolls of a width 25.3 mm and length 3 m. the tape silicone resists until a500f (260c) remains flexible to -60f (-50c) typical of the silicone tape applications insulating seal for electric cables electrical, automotive, aviation, marine, spatial, hydraulics, thermodynamics, etc.. masking in surface treatments (painting. Powder, plating, etc.) its great versatility makes it usable in many applications. for the automotive industry, electrical, sanitation, naval and hundreds of other uses. automotive electric hygienic satellite naval masking sealing insulation emergency repairs connections resistant to weathering protection against corrosion and cables tightening wires of irregular shapes sealed tubes, seals for rigging fittings for boats; ends of rope handles for tools; knobs. nb: This product is provided by the manufacturer without warranty of suitability 'for a specific purpose as conditions and applications are not analyzed individually. instructions for the correct use of tape self-sealing 1) clean the surface and cut the tape in the required length. (Normally 3-4 times the diameter to be wrapped) 2) remove the protective film 3) to keep one end of the retainer part on the tape to wrap and stretch. 4) maintaining wrap the tape in tension and make sure that at every turn the ribbon rests in part, at least in half, on itself. 5) ensure that the last round of tension both on the same surface of the tape already applied. for a specific purpose as conditions and applications are not analyzed individually. instructions for the correct use of tape self-sealing 1) clean the surface and cut the tape in the required length. (Normally 3-4 times the diameter to be wrapped) 2) remove the protective film 3) to keep one end of the retainer part on the tape to wrap and stretch. 4) maintaining wrap the tape in tension and make sure that at every turn the ribbon rests in part, at least in half, on itself. 5) ensure that the last round of tension both on the same surface of the tape already applied. for a specific purpose as conditions and applications are not analyzed individually. instructions for the correct use of tape self-sealing 1) clean the surface and cut the tape in the required length. (Normally 3-4 times the diameter to be wrapped) 2) remove the protective film 3) to keep one end of the retainer part on the tape to wrap and stretch. 4) maintaining wrap the tape in tension and make sure that at every turn the ribbon rests in part, at least in half, on itself. 5) ensure that the last round of tension both on the same surface of the tape already applied. (Normally 3-4 times the diameter to be wrapped) 2) remove the protective film 3) to keep one end of the retainer part on the tape to wrap and stretch. 4) maintaining wrap the tape in tension and make sure that at every turn the ribbon rests in part, at least in half, on itself. 5) ensure that the last round of tension both on the same surface of the tape already applied. (Normally 3-4 times the diameter to be wrapped) 2) remove the protective film 3) to keep one end of the retainer part on the tape to wrap and stretch. 4) maintaining wrap the tape in tension and make sure that at every turn the ribbon rests in part, at least in half, on itself. 5) ensure that the last round of tension both on the same surface of the tape already applied.

Registered users can share their experience with this product. Register to access all of the benefits reserved to registered users or click on login if you are already registered.