pellet stove Kit flue coaxial dn 80-130 exhaust air suction fumes made in Italy.

pellet stove Kit flue coaxial dn 80-130 exhaust air suction fumes made in Italy.

225,41 [+22% VAT]

 


REQUEST COST BEFORE PAYMENT


 

RELATED PRODUCTS

 
 
 
 
 
Product code PCKIT080
EAN 8028653008640
Category COAXIAL CHIMNEY
Brand MBM
Availability

Tip a friend

More questions ?

 
pin it

Suction kit and coaxial flue for pellet stove facade Kit MBM 80/130 for horizontal concentric coaxial configuration for watertight stoves with discharge into the facade (where permitted). This type of installation with front output is very simple to implement, because it does not require a lifting through the roof and consequently does not require any technical and expensive job. This allows the heater to operate watertight, taking the air outside the dwelling thanks to the coaxial pipe. This is mandatory in France for the BBC or RT2012 homes. The principle is very simple: the tubes have two distinct ducts. Outside the tube has a diameter of 130mm, and is the part inside which the air will pass, inside there is a second duct of diameter 80mm used for the evacuation of fumes. This makes it possible to pre-heat the incoming air to enhance the efficiency of the heat generator. The hole in the wall must therefore have a minimum of 140mm diameter. Once the hole made, the assembly of all the elements takes a few minutes. These tubes engage onto one another with male / female connection. ITEMS INCLUDED IN THE KIT: No.1 Union T 90 ° F GLAZED BLACK ø80 (COD. SMRT08080F) + CAP CONDENSA CLOSED BLACK nr. 1 ELEMENT SPLITTER ø80 / 130 COAXIAL BLACK (COD. PCGS08080) nr. 1 LINEAR ELEMENT 1 MT ø80 / 130 COAXIAL BLACK (COD. PCED01080) nr. 1 LINEAR ELEMENT 0.5 MT ø80 / 130 COAXIAL BLACK (COD. PCED02080) nr. 1 CURVE 90 ° ø80 / 130 COAXIAL BLACK (COD. PCCN90080) nr. 1 TERMINAL HORIZONTAL ø80 / 130 COAXIAL BLACK (COD. ......) nr. 1 HOSE IN ALUMINUM BLACK ø50 L. 1.5 MT (COD. FLXACN15050) + REDUCTION ø50 / 40 ALUMINUM NAT (COD. PPRC09050) nr. 2 BLACK ROSE ø130 (COD. PPROSONE130) nr. 4 CLAMP LOCKING ø130 COAX BLACK (COD. PCFB19080) nr. 3 CLAMP LOCK ø80 GLAZED BLACK (COD. PPFB19080X) nr. 1 HOSE BLACK WALL ADJUSTABLE ø80-130 (COD. PPFM80130) nr. 1 PROTECTION ANTI-HEAT (mounting optional) nr. 1 LINEAR ELEMENT 0:25 MT ø80 GLAZED BLACK (COD. SMED03080) (to be installed in case of spacing the wall, if necessary) seals in high temperature silicone including on all elements INSTALLATION INSTRUCTIONS: 1. Installing the TEE with its stopper condensation. 2. Installation element splitter. 3. Remove, if necessary, the control panel so that the vertical tubes may be positioned without touching or pass too close to the panel itself. 4. Installation of two coaxial elements 1 mt and 0.5 mt. 5. Installation of 90 ° bend. From this moment you can place your stove and track the exact location for the construction of the wall hole. 6.Installazione of the wall crossing terminal. The maximum thickness of the wall crossing is about 0.5 mt. It is necessary that this terminal is approximately 30 cm outside. The wall collar used to secure the rod to the wall (NB: not bear vertical loads). It is also important that the facade on which is formed this output is to be free from any obstacle that may disturb the discharge of combustion gases and / or the air supply (eg. Corner of the return wall). 7. Installation of an air intake pipe between T-fitting (item splitter) and the output of the stove. The reduction from ø50 to ø40 must be used only in the case where the output of the heater is of such dimensions. 8. In the kit there is a covering element of the T-fitting (anti-heat protection), but its assembling is optional. Installing the air intake pipe between T-fitting (splitter element) and the output of the stove. The reduction from ø50 to ø40 must be used only in the case where the output of the heater is of such dimensions. 8. In the kit there is a covering element of the T-fitting (anti-heat protection), but its assembling is optional. Installing the air intake pipe between T-fitting (splitter element) and the output of the stove. The reduction from ø50 to ø40 must be used only in the case where the output of the heater is of such dimensions. 8. In the kit there is a covering element of the T-fitting (anti-heat protection), but its assembling is optional.

Registered users can share their experience with this product. Register to access all of the benefits reserved to registered users or click on login if you are already registered.